 |
Die
Paarung des Stecker.
Der Steckersatz wird verwendet, um einen
Sensor mit Standardkabelbaum zu verbinden.
2-pin connector (digital output)
3-pin connector (digital input)
4-pin connector (analog input)
6-pin connector (power, CAN)
|
|
(PS-1000-5V)
Brake Pressure Sensor
For a sensor drawing on how to properly hook up this sensor to the RLC harness
click here. |
|
(PS-2000-12V)
Brake Pressure Sensor (2000 PSI)
click here. |
|
(Part# PS-100-12V)
Pressure Sensor (1-100 PSI) (Oil and Fuel) (12V, High Performance)
click here. |
|
(TS-300F-Fluid)
Temperature Sensor (300 F) (Oil and Water)
click here. |
|
(TS-300F-Air)
Ambient Air Temperature Sensor (300 F)
click here. |
|
(ITS-RLC-SPK)
Tachometer Sensor (Spark Plug Wire System)
Sensor kann
verwendet werden, wenn es kein sauberes
Drehzahlsignal am Fahrzeug gibt. Wickeln
Sie die Leitung direkt um das Zünkabel.
Ideal für Go-Kart-Anwendungen.
click here.
|
|
(ITS-8918)
Tachometer Sensor (Coil Over System)
Sensor für Drehzahlsignal, bei Fahrzeugen
mit integrierter Zündspule im
Kerzenstecker.
For a sensor drawing on how to properly hook up this sensor to the RLC harness
click here. |
|
(EGT-Kit)
EGT Sensor Kit (Amplifier & Thermo Probe K-Type)
EGT amplifier
EGT-Verstärker mit Thermoelement.
|
|
(EGT-AMP)
EGT Sensor (Amplifier Only)
Replacement EGT amplifier must be used with thermocouple probe. Plugs directly into harness.
|
|
(Thermo-Probe-K)
Thermocouple Probe (K-Type)
(Probe Only)
Replacement thermocouple probe must be used with EGT amplifier. Comes with probe and mounting bungs. Plugs directly into harness.
For a sensor drawing on how to properly hook up this sensor to the RLC harness
click here. |
|
(SS-1000)
Wheel Speed/RPM Sensor
Magnetic digital sensor, comes with magnet. Sensor can be used as a wheel speed sensor, RPM sensor, or driveline speed sensor.
For a sensor drawing on how to properly hook up this sensor to the RLC harness click here. |
|
Linear Position Sensors
Linear position sensors can be used for steering, throttle, or shocks. Available in four different sizes: 50mm (LPS-050)
100mm (LPS-100)
150mm (LPS-150)
200mm (LPS-200)
For a sensor drawing on how to properly hook up this sensor to the RLC harness click here. |
|
(SPS-12)
String Potentiometer - 12in.
String potentiometer sensor can be used for steering or throttle. Available in sizes up to 50 inches.
For a sensor drawing on how to properly hook up this sensor to the RLC harness
click here. |
|
(Relay-10A)
Relay for Digital Output - 10 Amp
Connect for fans, fire extinguisher, or warning lights.
Each relay provides the user with a normally open or normally closed connection so you can connect to anything.
For a sensor drawing on how to properly hook up this sensor to the RLC harness click here. |
|
(Relay-30A)
Relay for Digital Output - 30 Amp
Connect for fans, fire extinguisher, or warning lights.
Each relay provides the user with a normally open or normally closed connection so you can connect to anything.
For a sensor drawing on how to properly hook up this sensor to the RLC harness
click here. |
|
Lambda/Oxygen Sensor (Wideband)
Comes with sensor, amplifier, and mounting bungs.
For a sensor drawing on how to properly hook up this sensor to the RLC harness
click here. |
|
Data Acquisition Channel Expander
Instantly add additional analog and digital channels to
your Micro Pod dash by plugging in the
DACX. The expander can be used to connect to any analog sensor. Multiple expanders can be added the the Micro Pod unit. All additional analog and digital inputs are logged.
DACX 220
- 2 Analog Inputs, 2 Digital Inputs, 0 Digital Output
DACX 421
- 4 Analog Inputs, 2 Digital Inputs, 1 Digital Output
DACX 822
- 8 Analog Inputs, 2 Digital Inputs, 2 Digital Outputs
|
